Tip 1: Optimum use of your lighting with dimmable LEDs
Obviously, you will choose an LED spectrum with proven results for your crop. For many crops the light recipe has been developed, and we can select from a database of over 150 proven recipes. When HPS lighting is being replaced (partly) by LED, the total light level in the greenhouse usually increases significantly. In that case especially, it is useful to be able to dim the intensity of the LED lighting: with a dimmable installation you can respond to both the needs of the crop, weather conditions and the energy market, without making concessions to the uniformity of the light. An additional benefit of dimmable LEDs is that these become approximately 10% more efficient when dimmed. This decreases the energy usage per light unit.
Tip 2: Crop activity is the key
Dividing the assimilates created by photosynthesis is an important consideration. It is a pitfall to have the plant absorb all the lighting with an artificial lighting installation, but neglect to create circumstances for the plant to distribute the assimilates to the parts of the plant where we would like them to go, which are often the fruits and/or the flowers. Without taking the appropriate actions the crop could have too little evaporation, the plant temperature could stay too low, or absorb insufficient fertilizers.
Due to the absence of radiation heat, in some cultivations with LED screening is used more intensively and the windows stay closed more often to keep the heat inside the greenhouse. This can lead to a climate which is too passive, where the plant has problems evaporating. There are several options to keep the plant active. Key is the drainage of fluid around the plant. You can also consider extra air movement by fans for example, or by adding a (minimal) heating pipe in combination with a gap in the screen, and possibly leaving the windows slightly open. Active dehumidification by air handling units for example, is also a perfect option in combination with LED lighting. In that way you can actively screen and dehumidify with limited energy input.
In many cases we have seen that the energy saved by lighting with LED should be compensated slightly by a higher input of warmth. How much additional warmth input is needed differs strongly per crop situation, but the net energy savings compared to HPS are considerable when electricity and warmth are added. Moreover, in most situations, warmth also has a lower cost than electricity.
Tip 3: The plant rules
For optimal growth the plant should always be leading. Eventually the crop will show to what level the light offered will be converted into the desired development. Keep an eye on the water absorption, developmental speed, etc. and adjust the climate accordingly to keep the crop balanced. For many crops, in order to make the plant use the created assimilates in the right way, you need to steer more generatively compared to HPS. Consider, for example, realizing a larger DIF, moisture balance, (leaf)pruning strategy, and adjusting the EC or recipe of nutrients where needed. For your crop, a greenhouse temperature of 20 degrees with HPS feels very different to 20 degrees with LED. That means that with LED you should look more at the plant temperature instead of the surrounding temperature. It can also be a good idea to look at the plant temperature for the parts of the plant separately. When heat sources are applied differently this can have influence the temperature of the roots and fruits for example, compared to the head of the plant. An example of this is that in high wire crops the growth tubes are used much more with LED or hybrid lighting, to have a direct effect on the temperature of the fruits.
Tip 4: Control the plant temperature by screening
In many cases we see that growers who have an energy screen next to a shade screen, are more flexible and have more control over moisture and plant temperature compared to growers who only have a screen.
There is a big advantage in using an energy screen to control the plant temperature. Especially growers who are used to lighting with high intensity HPS are not always aware of the effect of the heat radiation from the lights, when the emission from outside is low er even negative. In many cases it could be a good option to close the energy screen almost completely, limiting the emission from the crop to the atmosphere, while air exchange and dehumidification can continue.
Tip 5: Keep calculating based on the light sum
When applying higher light intensities, light will be a limiting growth factor of a cultivation to a lesser degree. Artificial lighting will lead to stabile light sums in winter. Therefore, use the available light sum to create a stabile cultivation guaranteeing continuity. Light becomes less of a bottleneck, especially when warmth and light can be steered separately with LED lighting. This does not mean that you as a grower should not remain aware of the light sums that need to be reached and the growth- or production potential that entails. By realizing plant loads that are too high the crop becomes unbalanced, leading to difficult recovery in winter. Remain aware of a realistic plant density, harvest weight, harvest stage and pruning strategy.
How to make a successful LED cultivation
More and more growers make the switch to energy-efficient LED lighting and become convinced of the possibilities. To make the most of the potential, there are a number of ‘buttons’ to push to get the most out of your crop. Think of more than just the light, but of all growth factors in the greenhouse and let the plant guide you in your decisions.